3-Phase Electrical Power Calculator
This calculator shows the real 3-phase electrical power of your industrial equipment: motors, compressors, pumps, machines, or battery systems. Enter the phase-to-phase voltage, the current, and a few parameters. The tool then calculates the output power in kilowatts, the apparent power in kVA, the reactive power in kVAR, and the equivalent in horsepower.
Power system buttons
- DC: Direct current, for batteries and electronic systems.
- AC 1: Single-phase alternating current, for household and small equipment.
- AC 3: Three-phase alternating current, for factories, large motors and industrial systems.
How to use the calculator
- Choose your power system. Select DC for direct current (batteries, electronic systems), AC 1 for single-phase (small equipment, light networks), or AC 3 for 3-phase (factories, large motors, industrial buildings).
- Enter the voltage (V). Use the phase-to-phase voltage, meaning the voltage measured between two lines. It is usually shown on the equipment nameplate or measured with a multimeter.
- Enter the current (A). This is the current the equipment draws during normal operation.
- Enter the power factor (between 0 and 1). It shows how efficiently your installation uses electricity. For a motor, it is often between 0.8 and 0.9. For a purely resistive load such as a heater, it equals 1. If you don't know it, use 0.85 as a default.
- Enter the efficiency (%). This is the share of absorbed energy that becomes useful work. The rest is lost as heat or friction. A typical motor has an efficiency of about 85 to 95%.
Results explained simply
| Result | What it means | Unit |
|---|---|---|
| Output power | The power actually available to run your equipment. This is the value to use when sizing a machine. | kW |
| Apparent power | The total power your installation draws from the grid, including the non-working part. It is used to size cables, circuit breakers, and transformers. | kVA |
| Reactive power | The part of the energy that circulates without doing useful work, caused by coils and motors. It can lead to penalties on your electricity bill. | kVAR |
| Horsepower (hp) | The same power expressed in horsepower. Useful for comparing with a motor's datasheet, since many motors are rated in hp. | hp |
| Apparent impedance | The ratio of voltage to current (V ÷ A). It gives an idea of the load seen by the grid. | Ω |
The formulas, in plain terms
For a 3-phase system, the calculation works like this:
- Output power (kW) = √3 × Voltage × Current × Power factor × Efficiency ÷ 1000
- Apparent power (kVA) = √3 × Voltage × Current ÷ 1000
The number √3 (about 1.732) comes from the phase-to-phase relationship in a 3-phase system. The result is divided by 1000 to convert watts into kilowatts.
Horsepower in kilowatts: 1 hp ≈ 0.746 kW. To convert kilowatts to horsepower, divide kW by 0.746.
Practical example
Take a 3-phase motor supplied at 480 V, drawing 50 A, with a power factor of 0.85 and an efficiency of 90%:
- The apparent power is 41.57 kVA, which is what the grid must supply.
- The reactive power is 21.90 kVAR, the part that does no useful work.
- The output power is 31.80 kW, the energy actually available to the machine.
- This equals about 42.6 hp, consistent with the 0.746 kW-per-hp conversion.
These values help you choose the right circuit breaker, cable size, and machine rating.
Frequently asked questions
What is the difference between kW and kVA?
kW measures the power actually used. kVA measures the total power supplied by the grid. kVA is always greater than or equal to kW.
How do I convert kilowatts and horsepower?
Multiply horsepower by 0.746 to get kilowatts, or divide kilowatts by 0.746 to get horsepower. For example, 31.80 kW ÷ 0.746 ≈ 42.6 hp.
What is a phase-to-phase connection?
It is a connection measured between two phase conductors in a 3-phase system. The voltage entered in this calculator should be this phase-to-phase voltage (for example 480 V or 400 V), which is the value shown on most equipment nameplates.
Does this calculator convert single-phase to 3-phase?
No. This tool calculates power. It does not convert a single-phase supply into a 3-phase supply. A single phase to 3 phase converter is a separate piece of equipment. The calculator helps you size that equipment or your motor once you know its power needs.
Where do I find my power factor?
It is usually printed on the motor's nameplate or in the equipment datasheet. It can also be read from a power analyzer or your electricity bill.
Does this calculator work for DC?
Yes. Select DC. Power is calculated from voltage and current alone, with no power factor involved.
Are the results accurate?
The calculator gives a reliable estimate based on standard formulas. For safety sizing or a real installation, have the result checked by a qualified electrician or engineering office.